HPE Compute Solutions HPE0-S59 Dumps Questions

Jonnie Karnath2023-10-18T07:49:45+00:00

If you are aiming to successfully pass the HPE0-S59 HPE Compute Solutions exam, consider utilizing the comprehensive resources provided by Certspots. By studying their latest HPE Compute Solutions HPE0-S59 Dumps Questions, you will have access to the most up-to-date and relevant materials to thoroughly prepare you for your exam. In addition to this, Certspots offers a valuable opportunity to enhance your exam readiness through their free online HPE0-S59 practice exam. This practice exam allows you to assess your level of preparation and identify any areas that may require further attention. By taking advantage of these resources, you can greatly increase your chances of achieving success in the HPE0-S59 HPE Compute Solutions exam.

Page 1 of 2

1. Which statement about the HPE D3940 storage module is true?

SATA drives requires redundant 10 adapters to be installed in this module

Up to five modules can be installed in a single frame with Gen10 servers

it is configured through CLl available from HPE Synergy console

Only one type of drives (SATA, SAS, SSD) can be installed in each module

2. Refer to the exhibit.

Which statement about this logical JBOD is true?

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

This logical JBOD can be presented to the compute nodes in a different frame.

3. An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays

Where should you start the troubleshooting process?

At the iLO interface to verify whether the ILO Advanced license is properly applied

At HPE OneView Interface to verify whether the server is In the maintenance mode

At the iLO interface to verify whether the SSO certificate is removed from an iL

At HPE OneView Interface to verify whether the iLO processor is disabled

4. Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets

Which HPE compute system meets the customer requirements?

HPE ProLiant DL580 Gen10

HPE ProLiant OL380 Gen 10 Plus

HPE Synergy 480 Gen10 Plus

HPE Superdome Flex system

5. In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.

Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

Pause flood protection

sFlow

Storm control

Port flap protection

6. Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.

Which HPE compute system meets this customer's requirements?

HPE ProLiant DL380 Gen 10 Plus

HPE Synergy 480 Gen10 Plus

HPE ProLiant DL560 Gen10

HPE Superdome Flex 280

7. Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames

How will this change impact the customer environment?

The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.

The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.

The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.

The customer can add a new logical enclosure to an existing setup once all required licenses are added lo HPE OneView and associated with the new frames.

8. Which statement about HPE Apollo 2000 Gen10 Plus platform is true?

It is equipped with HPE Persistent memory by default

It can support a single processor only and up to 4 per chassis

It is fully managed using HPE OneView including all connections

It offers servers with AMD EPYC and Intel Xeon Scalable CPUs

9. Your customer added a new Ethernet network in HPE Oneview mat is used to manage their HPE Synergy platform.

When the customer tries to connect one of the compute nodes to this network through the server profile, this network is not available.

What must be done to fix this issue?

Check the Logical Enclosure settings and verify if the maximum number of networks allowed for this LE is reached.

To make this network available to use in the server profile, the customer must enable the Smart Link feature within network definition.

The newly created network must be added to the uplink set within the LIG, and Logical interconnect configuration must be updated from the LI

Check within the server profile which server hardware is used and perform the Refresh operation on this compute node to get the latest adapter information.

10. You modified a logical interconnect group mat is used to configure logical interconnects in five different logical enclosures.

What will be the impact of that change?

All physical interconnects from affected logical interconnects will be placed in a maintenance mode

All physical interconnects from the affected logical interconnects must he rebooted to activate the new configuration

All logical interconnects configured using this logical Interconnect group will report inconsistency

All logical interconnects configured using this logical interconnect group will be automatically updated

Page 2 of 2

11. Refer to the exhibit.

Which statement about this logical interconnect group is true?

Both modules are located in different frames for redundancy

For an uplink set, ports from different modules can be selected

interconnect modules are installed in interconnect bays 1 and 4

An additional license is required to change the enclosure count

12. Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

13. What is one of me benefits of using HPE Composer 2?

HPE Composer 2 has 128GB of memory and 4 AMD CPUs to improve performance of me management system

HPE Composer 2 modules are required to manage HPE virtual Connect SE 100GD F32 Modules for Synergy

The administrator can access an HPE Synergy Composer 2 appliance remotely to perform First Time Setup

A pair of HPE Composer 2 modules can manage 42 frames, compared to 21 frames managed by HPE Composer

14. Which statement about HPE Superdome Flex 280 is true?

It supports 2 to 8 sockets in 2-socket increments.

it cannot be managed using HPE OneView.

It must be equipped with at least 768 GB of memory.

It can support up to two nPars with an external RM

15. Which statement about manual orchestration during the firmware update is true?

It is supported only for logical enclosures with at least three frames

It provides an ability to select and update one side of the Interconnect topology at a time

It provides the ability to install an older firmware version than currently Installed In the interconnect

It allows all the interconnect modules to be activated manually at the same time.

16. Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex 280 They plan to manage new components using HPE OneView

What must be done to achieve this goal?

The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView

The customer should deploy an HPE OneView appliance for HPE Superdome Flex management

The customer must add a second Rack Management Controller for HPE Superdome Flex 280

The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy

17. A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?

Brocade 32GB Fibre Channel Switch Module for HPE Synergy

HPE virtual Connect SE 32 Gb FC Module for Synergy

HPE Virtual Connect SE 100 Gb F32 Module tor Synergy

HPE Synergy 12 Gb SAS Connection Module

18. Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options - SAS connectivity installed in the first fabric - FC connectivity Installed In the second fabric - Ethernet connectivity installed in the third fabric.

Which statement regarding this setup is true?

Each compute node must have at least 768GB of memory installed

Interconnect modules that provide SAS connectivity should be moved to the third fabric

Each interconnect module in each fabric must be properly licensed in HPE OneView

Compute nodes must have a second CPU installed to access the second fabric.

By Jonnie Karnath HP Free Dumps HPE Compute Solutions, HPE0-S59, HPE0-S59 Dumps Questions 0 Comments

Facebook Twitter LinkedIn Google + Email