NetApp NCSIE NS0-184 Dumps To achieve Good results

Jonnie Karnath2023-08-24T07:06:59+00:00

The NS0-184 exam is a crucial step towards earning the NetApp Certified Storage Installation Engineer, ONTAP certification. To ensure success on this exam, it is important for candidates to thoroughly prepare themselves. One valuable resource for candidates is the collection of free NetApp NCSIE NS0-184 dumps from Certspots. These dumps provide a wealth of practice questions and can help candidates to become more familiar with the exam format and the types of questions that will be asked. By dedicating ample time to practicing with these NS0-184 dumps, candidates can significantly increase their chances of success on the NS0-184 exam and ultimately achieve their NetApp certification. By taking a comprehensive and diligent approach to exam preparation, candidates can ensure that they are fully equipped to succeed on the NS0-184 exam and beyond.

Page 1 of 11

1. What does this CLI command do?

Cluster1: :> snapmirror create -source-path //vs1/vs1_root -destination-path //vs1/vs1 m2 -type LS

It creates a data protection mirror relationship.

It limits the SnapMirror bandwidth.

It creates interduster SnapMirror peering.

It creates a load-sharing mirror relationship.

2. Click the Exhibit button.

You are attempting to add a new ONTAP 9.7 node to your ONTAP 9.8 NetApp cluster.

After attempting to add the node, it fails as shown in the exhibit.

What are two nondisruptive ways to add the new node to your ONTAP cluster? (Choose two.)

Revert the cluster from ONTAP 9.8 to ONTAP 9.7.

Re-initialize all the nodes in the ONTAP cluster with ONTAP 9.7.

Upgrade the new node from ONTAP 9.7 to ONTAP 9.8.

Add the node using the -allow-mixed-version- parameter.

3. A customer has an AFF A800 with 24 internal drives and is running out of storage capacity. In this scenario, which action will solve this issue?

Insert more internal NVMe SSD drives.

Attach an additional DS212C shelf, filled with drives.

Attach an additional DS460C shelf, filled with drives.

Insert more internal SSD drives.

4. You have completed the installation of a 4-node cluster. The customer did not purchase management switches and will not allow your laptop on the network.

In this situation, what are two valid procedures that will allow you to collect the Config Advisor output? (Choose two.)

Bring a switch that allows you to connect your laptop to all the switches and controllers.

Connect to a single controller in the cluster since it can run commands on every node.

Ask the customer to install and run Config Advisor on one of their PCs on the network.

Connect four USB serial cables to your laptop to allow you to connect to all four controllers.

5. Which two configurations use root-data-data partitioning? (Choose two.)

FAS8080 with 1.8 TB external SAS drives

AFF A800 with 3.8 TB internal NVMe SSD drives

FAS2650 with 1.8 TB internal SAS drives

AFF A220 with 3.8 TB internal SSD drives

6. What should you do to change the data protocol of a LIF?

Delete and re-recreate the LI

Add the new data protocol to the LI

Put the LIF in another broadcast domain.

Shut down the assigned port.

7. Your customer wants to know more about the network configuration within the cluster.

In this scenario, which statement is correct about a LIF?

A LIF is a port that provides physical connections.

A LIF is created within a broadcast domain and contains a pool of IP address.

A LIF is an IP address or a WWPN that is associated with a port.

A LIF separates network domains to access cluster data.

8. In which scenario must ACP be out-of-band?

when using DS4243 shelves with SATA drives and I0M6 modules

when using DS4243 shelves with SATA drives and IOM3 modules

when using DS4243 shelves with SSD devices and IOM12 modules

when using DS212C shelves with SSD devices and IOM12 modules

9. You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.

In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

route

NTP

DNS

VLAN

10. You finished a new installation and executed Config Advisor successfully. You review the physical racking and cabling on one of the controllers, and notice an amber light that was not previously on.

Which two actions should you perform before you turn over the cluster for production? (Choose two.)

Remove cables connected to the controller until you find the one responsible for the controller issue.

Review AutoSupport messages which could explain the controller state.

Execute Config Advisor again to check for new errors.

Let the customer know the cluster is operating normally while the amber LED is on.

Page 2 of 11

11. You install a 4-node cluster with an AFF A400 HA pair and a FAS8300 HA pair. After setup, you are asked to review the audit logs on each controller from a Web browser.

In this scenario, which method provides access to the logs from a Web browser?

ADP

DNS

ACP

SPI

12. Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

to provide a direct connection for the SnapMirror Synchronous (SM-S)

to install cross-site cluster management switches

to provide connectivity for NVRAM over iWARP

to enable SyncMirror replication

13. You have a 2-node switchless cluster named clusterA. You are planning on adding two additional nodes to clusterA.

What must you consider before you add the addiHonal nodes to clusterA?

Convert clusterA to a switched cluster by migrating the data lIFs from direct connect to die cluster interconnect switch.

Convert clusterA to a single-node cluster.

Convert clusterA to a switch** cluster by migrating the cluster LIFs from direct connect to the cluster interconnect switch.

Use direct connect to add the additional nodes to cluster

14. Which tool is used to compare or check the dependencies of individual software and hardware components?

Solution Builder

FMC_DC

Interoperability Matrix Tool (IMT)

Net2

15. Click the Exhibit button.

Referring to the numbers shown in the exhibit, which port on an AFF A220 controller is used as port e0M in ONTAP?

16. Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)

The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.

The LIFs must use the default intercluster service policy.

The LIFs must be in dedicated broadcast domains an IPspaces.

At least one LIF per node is required on each cluster.

17. Exhibit:

You finished installing an ONTAP cluster and must inform the customer of the completion. As part of this exercise, you will show how to configure the ONTAP cluster using ONTAP System Manager, so that NetApp will receive notifications of any future issues.

What would you select to allow the customer to receive this information?

General

Date and Time

Users

AutoSupport

18. What is the minimum number of disks required in a SAS shelf?

half of the shelf's capacity

one

two

there is no minimum

19. Which command would be used to measure the throughput and latency of traffic between nodes?

qos statistics workload performance show

cluster ping-cluster

network test-path

statistics node show

20. You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.

Which tool would be used to accomplish these tasks?

System Diagnostics

Cloud Insights

Active IQ Config Advisor

Active IQ Unified Manager

Page 3 of 11

21. You are asked to install six shelves to a production cluster. The cluster is running clustered Data ONTAP and is a 4-node cluster. All six shelves will be cabled to the same HA pair. The customer wants you to assign all the new disks to a single node in the cluster.

Which three tools would help you accomplish this task? (Choose three.)

the Hardware Universe Web-based tool

the Synergy application

the Config Advisor application

the My AutoSupport Web-based tool

the System Setup application

22. To ensure that your customer’s cluster is robust and operational, you need to be familiar with configuration best practices.

Which three practice rules should you always follow? (Choose three.)

Keep all nodes in the cluster on the same version of ONTA

Use LIFs with defined failover policies.

Remove failed disk drives once a year to maintain minimum interruption in your controller stability.

All power supply units should be plugged into the same power grid.

Do not use the root aggregate for storing data.

23. Which two commands verify that AutoSupport is working as expected?

autosupport test show

autosupport history show

autosupport check show

autosupport show

24. A customer has a standard request for information regarding the installation, configuration, usage, and maintenance of this NetAPP equipment.

What is the appropriate priority level to use when he open a case?

25. What, if any, cabling configuration does this command output indicate?

https://www.nwexam.com/files/nwexam/download/NS0-180_25_A.PNG

Shelf 22 has a faulty 10M in slot

The node is connected only to the B paths of shelf 22, so it is not MPHA compliant.

Shelf 10 is assigned to the local node and shelf 22 belongs to the partner node.

The shelves are correctly cabled for MPH

26. Set the adapter to status-admin up.

27. You are creating an aggregate on a new FAS8200 with two DS224C shelves. Your customer wants to be able to use the Disk Maintenance Center.

In this scenario, what is the minimum number of spare disks required per node and disk type?

28. You are asked to installed a new cluster with six FAS8060 nodes. While running Config Advisor, you determine that there is a newer firmware version for 16 HDDs.

How should this situation be handled?

Prior to leaving the site, advise the customer that firmware is included with the version of ONTAP they selected.

Unless the customer advises otherwise, upgrade the firmware on the HDDs to correct the Config Advisor error.

Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.

Prior to leaving the site, confirm the version of ONTAP that the customer wanted installed to correct the Config Advisor error.

29. You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.

Which statement is correct in this scenario?

Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.

Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.

Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.

Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.

30. Select the Exhibit tab.

Referring to the exhibit, a customer wants to migrate LIF lif1 iscsi to node cluster1-02 port e0d, but they receive an error.

What is the cause of this error?

The LIF is not properly configured.

The destination port is not available.

This type of LIF cannot be migrated.

The LIF does not have a failover group.

Page 4 of 11

31. What are two requirements for a 6-node cluster? (Choose two.)

network connectivity from the cluster to the customer's infrastructure

dedicated switches for the cluster interconnect

SAN connectivity from the cluster to the customer's infrastructure

dedicated switches for the cluster management

32. A host cannot connect to the namespace configured on an NVMe-enabled SVM.

In this scenario, what are two reasons for this problem? (Choose two.)

The namespace has not been added to the subsystem

The namespace has not be added to the igroup

The igroup has an incorrect NQ

The subsystem has an incorrect NQN

33. What are two ways to obtain customer licenses for a new ONTAP system? (Choose two.)

Access the NetApp Support site.

Open a support ticket.

Access the Field Portal site.

Access NetApp Knowledge Base.

34. Customer wants to modify the properties of their SPI Web services as shown in the exhibit.

What is the reason for the error?

The customer is trying to modify a service by specifying the wrong type of SVM (Vserver).

The customer is trying to modify a service that does not exist.

The customer is trying to modify a service by specifying the wrong service name.

The customer is trying to modify a service by specifying incomplete parameters.

35. A customer wants to graphically manage a new clustered Data ONTAP system.

Which tool should the customer use?

System Setup

OnCommand System Manager

HostAgent

StorageGrid

36. A customer is settings up a new cluster. The customer notices that there are many management ports on the cluster. The customer is know the purpose of the node management network LIF.

What do you tell customer in this scenario?

The node management LIF provides multiple IP address for managing a particular node in the cluster at the hardware level and is used for system maintenance.

The node management LIF is associated with a storage virtual machine (SVM) and is used for communicating with client.

The node management LIF provides a dedicated IP address for the entire cluster and can fail over to any node management or data port in the cluster.

The node management LIF provides a dedicated a IP address to managing a particular node in the cluster and is used for system maintenance.

37. You are adding nodes to an existing cluster. In this scenario, which three statements are correct? (Choose three.)

If you are adding a second node to a single-node cluster, the second node must have been installed, but the cluster network can be configured later.

You must add a cluster switch for every two nodes.

If you are adding nodes to a multiple-node cluster, more than half of the existing nodes in the cluster must be healthy.

The switchless cluster functionality is supported only in a single or two-node cluster.

If you are adding nodes to a two-node switchless cluster, you must have installed and configured the cluster management and interconnect switches before adding additional nodes.

38. After completing an installation, the customer wants to know how they can manually open a new technical case with NetApp Global Support.

What are three ways to accomplish this task? (Choose three.)

Use the support site.

Use the NetApp Field Portal.

Use the mobile app.

Use a telephone.

Use AutoSupport.

39. When you configure EMS to send event notifications, which customer data do you need to include? (Choose two.)

the IP of the company's web server

the name of the mail server

the administrator's phone number

the SNMP community string

40. According to NetApp best practices, which tool should be used to verify the system configuration?

Synergy 6.1

OnCommand System Manager

Config Builder

Config Advisor

Page 5 of 11

41. When you start a new Service Event Report, what must be entered first?

the case ID number

the project number

the node serial number

the sales order number

42. Which switch vendor is supported for the cluster network switches?

Juniper Networks

Cisco

Brocade

Hewlett-Packard

43. A customer is installing a new system and has determined that they have a broken disk.

What information is required to open a NetApp Support case?

disk HBA firmware and serial number

mainboard rev. id

serial number or system ID

disk shelf serial number and shelf ID number

44. What is the main function of ACP?

it allows cabling the shelf to two additional controllers.

It allows the controller to use Ethernet instead of SAS to fetch the storage data.

it allows the controller to nondisruptively reset the SAS expanders.

It enables the automatic shelf ID assignment.

45. A customer has a 6-node AFF A700 cluster and wants to add four nodes without having to update license functionality for each node manually.

In this scenario, which type of license provides this functionality?

Demo License

Site License

Standard License

Evaluation License

46. Regarding clustered Data ONTAP 9, what happens to the roles of the on board ports, HBAs, and NICs?

These roles are assignet when LIFs are created.

These roles are assigned based on the controller type.

These roles are predefined and must be changed before creating your LIFs.

The roles are divided into two categories: Data Management and Node Management.

47. You completed an ONTAP cluster deployment as a reseller engineer. During the knowledge transfer process to the customer, they ask for proof that the array has correct multi-path HA cabling deployed and that the array is error free.

Which documentation output would you present to the customer to satisfy this requirement?

Active IQ Unified Manager output

NetAppDocs output

Config Advisor output

Active IQ OneCollect output

48. After the Installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster.

In this scenario, what are two ways to trigger a new AutoSupport? (Choose two.)

Use the ping command on the mailhost.

Use the OnCommand Unified Manager GU

Use the OnCommand System Manager GU

Use the system node autosupport invoke -type test command.

49. You are asked to Install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf.

Which shelf would you add to this cluster?

a DS224C shelf fully populated with SAS drives

a DS224C shelf fully populated with SATA drives

a DS2246 shelf fully populated with SSD drives

a DS4486 shelf fully populated with SATA drives

50. You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.

In this scenario, how would you add the shelf?

Add the shelf to the existing stack.

Create a new stack on the HA pair to add the shelf.

Connect the shelf to an HA pair with NSE drives.

License NSE and add the shelf to this HA pair as a new stack.

Page 6 of 11

51. A customer ordered two new DS224C shelves. The Customer wants you to add these shelves to an existing stack which consists of two DS2246 shelves.

Which statement is true in this scenario?

You need to order additional cables to expand the existing stack.

Mixing DS224C and DS2246 shelves in the same node is not supported.

You cannot mix DS224C and DS2246 shelves in the same stack.

DS224C shelves are supported with only new HBAs.

52. Clustered Data ONTAP supports which three ifgrp modes? (Choose three.)

Static Multi-mode

Dynamic Multi-mode

Linked Multi-mode

Single-mode

53. According to NetApp, how many interswitch links (ISL) for a CN1610 switch are recommended for the cluster network?

4 ISLs

3 ISLs

2 ISLs

1 ISLs

54. Which statement regarding Epsilon is true?

The node holding the epsilon has extra fractional vote weight.

Whenever a new node is added, the epsilon is automatically reassigned to this node.

The epsilon acts as a tiebreaker in a 2-node cluster.

Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.

55. You just installed a new AFF A220 2-node cluster without additional disk shelves. When you review the Config Advisor output, you notice that your SAS cabling appears to be single-path HA.

In this scenario, which statement is true?

The Config Advisor version you are using requires a plugin for AFF controllers.

AFF A220 controllers with internal disks support only single-path H

Cable controller 1 0a to controller 2 0a, and cable controller 1 0b to controller 2 0b.

Cable controller 1 0a to controller 2 0b, and cable controller 1 0b to controller 2 0a.

56. Which statement regarding a node-management LIF is true?

The LIF can be set only on the built-in node-management port - e0

The LIF must use two switches for redundancy purposes.

The LIF can be set up on a dedicated VLAN in the data network.

The LIF can be set up on a dedicated VLAN in the cluster network.

57. You are preparing to install a new cluster at a customer site.

Which two concerns must you address with the customer in this scenario? (Choose two.)

Is there an uninterruptible power supply (UPS) system?

Is there enough rack space available?

Are the power requirements fulfilled?

Is there a fire extinguishing system?

58. You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.

In this scenario, which two health outputs would this command show you? (Choose two.)

data switch cabling

cluster switch cabling

shelf connectivity

node CPU utilization

59. A 2-node cluster using the NetApp CN1610 switch requires how many ISLs?

60. You are preparing to install a new clustered Data ONTAP system.

Which tool prepares all the relevant customer and configuration information?

AutoSupport

Cluster Config Builder

OnCommand System Manager

Config Advisor

Page 7 of 11

61. Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it.

In this scenario, how would you access Node 4’s management interface?

You must use the Service Processor; node management LIFS do not fall over between nodes.

You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.

You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.

Connect to the node management on Node 3 and then use the HA interconnect to access node 4.

62. You want to add an AFF A400 HA pair to an existing cluster.

In this scenario, which LIF type is required?

cluster-mgmt

intercluster

data

node-mgmt

63. You have to disable a switch that is connected to a port on your FAS2750. You notice that the LIFs that are associated with this port are migrated to a port that is not expected.

In this scenario, what would cause this behavior?

The network port is configured incorrectly.

The broadcast domain is configured incorrectly.

There are no online ports within the same failover group.

The network failover port is not licensed.

64. A customer is using a Cisco Nexus 5020 as a cluster network switch.

What would be used as a management network switch in this scenario?

Cisco Nexus 5020 1GbE ports

Cisco Nexus 5020 Expansion Module

Cisco Catalyst 2960

Cisco Catalyst 5000

65. Select the Exhibit tab.

You finished the installation of a new FAS8200 system. The customer wants to use FC and 10G Ethernet but only has the onboard UTA2 ports available.

Referring to the exhibit, which two sets of ports would the customer use? (Choose two.)

e0e, 0f and e0g, 0h

0e, 0f and e0g, e0h

0e, e0f and 0g, e0h

e0e, e0f and 0g, 0h

66. You need to verify the configuration currently loaded on a Cisco Nexus 3132Q-V cluster switch after applying the RCF.

Which command will accomplish this task?

Use the show bootvar command.

Use the verify config command.

Use the show startup-conf command.

Use the show running-config command

67. You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.

In this scenario, what are two valid actions for this installation? (Choose two.)

Add the new nodes to the existing cluster and switches.

Create a new 2-node switched cluster that uses the CN1610 cluster switches.

Create a new 2-node switchless cluster.

Migrate the existing cluster to new switches and add the new nodes.

68. Your customer asks you how he can use the root aggregate to store data.

What should you tell him?

He can only use the root aggregate to store data if he changes the RAID group to RAID 4.

He can use the root aggregate only if he changes the name of the root aggregate to reflect a IP different aggregate naming convention.

He can use the root aggregate for storing any data.

He should not use the root aggregate for storing data, but create a new aggregate instead.

69. After you deploy a 4-node AFF A220, you want to upgrade the ONTAP version of the cluster.

In this scenario, before the upgrade, which advanced CLI command is used to locate epsilon?

clustering ring show

cluster ha show

cluster show

cluster image show

70. You installed a new FAS9000 with SAS disk shelves. You want to use write cache in this environment.

In this scenario, what should you do to accomplish this task?

You need to buy an SSD and set it up as a storage pool for write cache that is used for the aggregate that you need.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the node that had an SS

You need to set up the caching policy as your requirement by using the Flash Cache NVMe module.

You need to buy an SSD and set it up as a Flash Pool for write cache that is used at the aggregate that had an SS

Page 8 of 11

71. Which keyboard combination enables you to access the Service Processor (SP) or the Board Management Control (BMC) from the system console CLI?

Ctrl + D

Ctrl + G

Ctrl + S

Ctrl + C

72. What is the purpose of a mailbox disk?

for shipping defective drives back to NetApp

for storing HA partner information

for logging

for sending AutoSupport mail

73. You are performing an installation of a clustered Data ONTAP and you reach the AutoSupport configuration point. You configured AutoSupport with all of the customer's information.

But when you trigger AutoSupport, the customer says that they did not receive the message, and neither did NetApp.

Which two actions must be verified? (Choose two.)

You can ping the mailhost from the NetApp storage systems.

The customer has enabled port 25 from the storage controllers on their firewall.

The customer has enabled routing of email-based messages from the storage controllers on their email server.

You can ping the NetApp Support site from the storage systems.

74. Which two optional add-on software products must be licensed? (Choose two.)

CIFS

SnapRestore

SyncMirror

OnCommand System Manager

75. Referring to the exhibit, which statement describes the duster network used by the cluster interconnect ports?

The network used to allow all nodes to communicate with the users for data acces

The network used to allow all nodes to communicate for internal (private) data access

The network that allows all nodes in the cluster to have direct access to every other node's disk shelves

The network used to allow all nodes to communicate with the customer (or management access

76. Exhibit:

You have an 8-node cluster, and sometimes the data LIFs fail over to a non-working port.

Referring to the exhibit, what must you do to solve this problem?

Configure more than one IPspace.

Configure the MTU consistently across the cluster

Configure the correct Ethernet ports in all broadcast domains.

Configure the LIFs using separate home nodes.

77. You have just installed a new FAS2650 HA for your customer. You are now configuring the AutoSupport transport section.

In this scenario, what Is the NetApp best practice for this task to allow AutoSupport (ASOD)?

Use SMT

Use HTTP

Use HTT

Use SS

78. You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.

Which tool would you use to accomplish this task?

Active IQ scheduled reports

NetAppDocs output report

ONTAP System Manager

Active IQ Config Advisor worksheet

79. After completing the installation of an AFF A800 ONTAP AI cluster, you are asked which contacts are available for additional help in obtaining immediate assistance in solving P1 issues.

In this scenario, what do you tell the customer?

Contact NetApp Support using chat.

Use Guided Problem Solving.

Contact NetApp Support by telephone.

Use the NetApp KB TV channel.

80. Config Advisor reports that you have a single point of failure on a stack of shelves.

After investigation, you have assigned the following ports to each stack:

stack 1 - ports 0a and 0b

stack 2 - ports 3a and 4b

stack 3 - ports 4a and 3b

In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)

Cable stack 3 to ports 4a and 0b.

Cable stack 2 to ports 4a and 4b.

Cable stack 1 to ports 0a and 3b.

Cable stack 3 to ports 3a and 3b.

Page 9 of 11

81. Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster ping-cluster node1 command and received the output as shown in the exhibit.

Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose two.)

2 paths up, 0 paths down (TCP check)

2 paths up, 0 paths down (UDP check)

larger than PMTU communication succeeds on 4 path(s)

basic connectivity succeeds on 4 path(s)

82. You installed a new FAS8200 cluster and are configuring important EMS event notifications to be sent to the customer.

Which address must be set up for e-mail notifications in this scenario?

LDAP address

site address

partner address

mailserver address

83. Exhibit:

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.

For a high availability, which ports should swap Ethernet cables?

Swap node2:e4a and node2:e8a.

Swap node1:e8a and node2:e4a.

Swap node1:e4a and node1:e8a.

Swap node1:e4a and node2:e4b.

84. You have completed a clustered Data ONTAP installation for a new customer. You are now ready to hand off the system to the customer.

Which three actions should you take at this stage in the installation process? (Choose three.)

Show the customer how to open a case with NetApp Support.

Demonstrate System Manager and its functionality.

Tell the customer to call their sales representative if there are further questions.

Tell the customer you are finished and then leave the site.

Show the customer how to set up a support account.

85. A customer learns that a certain NetApp tool allows remote data collection, intelligent core file handling, and notification of down storage controllers for technical support analysis and troubleshooting.

What is the name of this tool?

RSA

HWU

Synergy

HW Assist

86. When you install a new ONTAP 4-node cluster, which network type is required?

data network

peering network

cluster interconnect

intercluster network

87. You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.

In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?

Interoperability Matrix Tool

ConfigBuilder

Active IQ Config Advisor

Active IQ Unified Manager

88. You are preparing to install a new 4-node cluster for your customer. They want to use NetApp CN1610 cluster switches that they previously purchased.

Which software must be downloaded to ensure that you are well prepared for this installation?

You must download CN1610 firmware and RCF files compatible with the clustered Data ONTAP version that your customer wants to use.

You must download the Cisco configuration files compatible with the clustered Data ONTAP version that your customer wants to use.

You must download ATTO Fibre Bridge firmware.

You must download the System Setup tool.

89. Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

Active IQ

Config Advisor

NetAppDocs

Fusion

90. Poppy Pet Care Kennels offers short-term accommodation for dogs whilst their owners are on holiday. The managing director of the company has initiated a project to create a new website that will allow owners to view kennel availability, book kennel accommodation and allow them to monitor their dogs whilst they are away, via a webcam.

The system will also allow kennel assistants to plan the dogs’ feeding times and schedule kennel maintenance.

Customers will be able to leave feedback on the website, which will be reviewed by the quality manager who may respond to comments made by the customer.

The following are potential actors:

A) Poppy Pet Care Kennels

B) Kennel assistants

C) The managing director

D) Customers

E) Quality manager

Which of these would be drawn as actors on the use case diagram?

A, B and C

A, D and E

B, C and E

B, D and E

Page 10 of 11

91. In an ONTAP switched cluster, which three types of traffic travels over the cluster network? (Choose three.)

intercluster SnapMirror

intracluster SnapMirror

Epsilon voting

cluster database replication

remote cluster peering

92. A customer is asked to install a new AFF ASA A700 system. During the installation, the customer asks if ONTAP 9.8 is supported with their host’s OS version running Windows 2016.

In this scenario, which NetApp tool would verify supportability?

ONTAP System Manager

Active IQ Unified Manager

Active IQ OneCollect

Interoperability Matrix Tool

93. A customer ordered a new ONTAP system and is concerned about how you will cable the system using multipath HA with the new system.

According to NetApp, what are the guidelines to accomplish this task?

Systems using hardware disk ownership can only be cabled using single path cabling practices.

Multipath HA is required on all HA pairs.

Multipath HA is required on all HA pairs except for some FAS25xx and FAS26xx system configurations.

Multipath HA cabling is required for SSD shelves.

94. You are adding two new nodes to an existing switchless 2-node cluster.

In this scenario, which two statements are true? (Choose two.)

You must make sure that the existing nodes are healthy and that all cluster links are up

You need to schedule downtime to add these two nodes

The existing cluster must use clustered Data ONTAP 8.1 or later software

You first need to install the cluster interconnect switches to the existing cluster

95. You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.

In this scenario, which network interface is needed for each SVM to register with the name service?

SVM data LIF

SVM management LIF

node management LIF

intercluster LIF

96. You are installing a new cluster with a pair of NetApp CN1610 switches.

Which three statements describe how the ports are configured according to NetApp best practices? (Choose three.)

Ports 13-16 are designated as cluster host ports.

All ports have standard frames enabled.

Ports 13-16 are designated as Inter-Switch Links (ISLs),

Ports 1 12 are designated as cluster host ports.

All ports have jumbo frames enabled.

97. Advanced Drive Partitioning (ADP) is available for which three NetApp systems? (Choose three.)

FAS80XX with SAS and SATA disks

FAS25XX with SSD disks

FAS80XX with SATA disks

FAS25XX with SATA disks

FAS80XX with SSD disks

98. A customer requires encryption at rest on every node root volume.

In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

NVE

IPsec

NAE

NSE

99. Which statement describes an SVM?

An SVM is a node in the cluster

An SVM is a storage volume type

An SVM is a logical device that shares data

An SVM is a logical network interface

100. A remote administrator is connecting to a cluster from a different remote network.

According to NetApp best practices, which type of LIF routing is required to accomplish this task?

cluster LIF

data LIF

cluster management LIF

intercluster LIF

Page 11 of 11

101. You are preparing to add a 2-node AFF A250 system to an existing 4-node AFF A800 cluster with Cisco Nexus 3232C switches. The cluster switches are currently running the Cluster-HA RCF.

In this scenario, which two steps are required to install the AFF A250 system? (Choose two.)

Load the Storage RC

Cable the AFF A250 nodes to the next free ports on the switch.

Cable the AFF A250 nodes to the breakout ports on the switch.

Load the Cluster-HA-Breakout RC

102. You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager.

In this scenario, what caused this problem?

Breakout cables were used and the second port on the same ASIC became disabled.

This is a hardware error and you must open a case with NetApp Support.

You must first enable the ports using the network port modify command.

You are missing a license to enable those ports.

103. Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.

In this scenario, what would you tell the customer?

104. Exhibit:

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.

Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

Relocate the switches or the AFF A400 so that the distance is less than five meters.

Install 10 meter NetApp supported copper cables.

Change the requirement for Ethernet cables.

Change the requirement for optical cables.

105. You are asked to install four DS2246 shelves onto a 2-node cluster using FAS8060s. This system currently has two stacks in use. These stacks are currently using SAS ports 0a, 0d, 3a, and 3b.

Which pair of SAS ports should be used in this scenario to create a new stack?

0b, 3d

0b, 3c

0c, 3c

0c, 3b

106. You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.

How do you verify your configuration?

Use the storage show disk -p command.

Use the storage disk option show command.

Use the disk show -fields initiator command.

Use the sysconfig command.

107. You have a 4-node FAS8060 cluster. You are using the vol move command to relocate a volume from an aggregate on node 1 to an aggregate on node 4.

In this scenario, which network is used for the traffic being relocated?

the node management network

the HA interconnect

the Intercluster network

the cluster interconnect

108. Click the Exhibit button.

A customer wants to replace their ONTAP cluster CN1610 switches with Cisco Nexus 3132Q-V switches. They want to perform a non-disruptive upgrade.

Referring to the exhibit, which cable will be required to non-disruptively migrate to the new switches?

a 10GbE SFP+ to SFP+ cable

a 100GbE QSFP28+ to 4x25GbE SFP28+ cable

a 40GbE QSFP+ to QSFP+ cable

a 40GbE QSFP+ to 4x10GbE SFP+ cable

109. You have added two new AFF A250 nodes to an existing 4-node cluster with NetApp CN1610 cluster network switches. Although the nodes can join the cluster, the storage failover show command output shows that the NVRAM log is not synchronized, and it cannot reach the partner over an HA interconnect.

In this scenario, which two statements are true? (Choose two.)

The AFF A250 requires switches with 40GbE port support.

The AFF A250 uses different ports for the cluster and the HA interconnect.

The AFF A250 requires switches with 25GbE port support.

The AFF A250 uses the same port for the cluster and the HA interconnect.

110. You have just finished installing and configuring an ONTAP cluster for a customer.

In this scenario, which product collects information and produces site documentation?

NetAppDocs

Inventory Collect Tool

SnapGathers

Active IQ OneCollect

Facebook Twitter LinkedIn Google + Email