Latest Huawei H35-481_V2.0-ENU Dumps Questions - Pass Exam With Ease [2023]

Latest Huawei H35-481_V2.0-ENU Dumps Questions – Pass Exam With Ease [2023]

Jonnie Karnath2023-04-25T02:16:47+00:00

Huawei H35-481_V2.0-ENU dumps questions are designed to help you pass the HCIP-5G-RAN V2.0 Exam exam with ease. It covers all the topics and concepts that you need to know to pass the exam. They are designed by industry experts who have in-depth knowledge of the subject matter and can provide you with the most relevant and accurate information. Using Huawei H35-481_V2.0-ENU dumps questions will give you a realistic exam experience, as the questions are similar in format and difficulty to the actual exam questions. This will help you prepare better for the exam and reduce exam anxiety. By using these Huawei H35-481_V2.0-ENU dumps questions, you can increase your chances of passing the exam on your first attempt.

Page 1 of 2

1. The STR CROSFEEDTST command can be used to check for crossed feeder connections of an AAU.

True

False

2. Which of the following parameters In the NR MIB message indicates the time-domain position of CORESET 0?

System frame number

Most significant four bits of PDCCH-configSIBl

SSB-subcarrier offset

Least significant four bits of PDCCH-configSIBl

3. If the subcarrier spacing (SCS) of a low-frequency cell Is 30 kHz and the bandwidth of each RB Is 360 kHz, theoretically, what value should the noise (dBm) over the air interface be?

-105

-116

-120

-97

4. Which of the following may cause exceptions In the GPS clock source?

High signal attenuation is caused due to improper GPS remote distance.

The antenna feeder between the base station and the GPS is faulty, for example, the cable is disconnected.

The GPS is not installed in the correct position, and the number of locked satellites is less than 4.

The GPS satellite card Is faulty.

5. What does it mean when the RUN indicator of anAAU is blinking green (on for is and off for Is)?

There is power supply, but the board is faulty.

The board is working properly.

Software is being loaded to the board, or the board is not started.

There is no power supply, or the board is faulty.

6. How many OM channels does a gNodeB support at most?

7. In CRAN deployment, the one-to-four cascading mode can be used for GPS clock configuration.

How many BBUs at most can a GPS be connected to?

8. Which of the following scenario using the radio data planning file In the MAE-Deployment?

Configuration of parameters in multiple MOs

Batch reconfiguration of NEs

Reconfiguration of a single NE

Configuration of parameters in an MO

9. Which of the following synchronization rasters can be used by a UE during a cell search?

17.28MHz

1200kHz

1.44MHz

100kHz

10. Which of the following boards can be blocked by running the BLK BRD command?

BBP

DUPEU

AAU

RRU

Page 2 of 2

11. If multiple IP addresses with different next hop addresses are planned for the gNodeB, which of the following route configuration modes is not applicable?

Destination address route configuration

Source address route configuration

Direct route configuration

12. In NSA networking, X2 Interface self-setup between the 4G and 5G base stations falls.

Which of the following are possible causes?

The 5G and 4G base stations belong to different PLMNs.

Cell setup fails on the LTE side.

The number of links established over the LTE X2 interface exceeds the board specifications.

The self-setup switch is not turned on.

13. Which of the following Information Is contained in a master Information block (MIB)?

System frame number

PDCCH ConfigSIB1

dmrs-TypeA-Position

Offset from PointA

14. Which of the following methods can be used to locate faults on the user-plane path?

GTPU trace

Cell DT trace

SCTP tracing result

NG interface trace

15. Generally, the gNodeB synchronizes time information from the OSS.

Which of the following commands is used to configure the IP address of the time server?

ADD IPCLKUNK

ADD GPS

ADD NTPC

ADD OMCH

16. If the configuration data of a new BTS5900 base station cannot be loaded remotely, which of the following can be used to for local data configuration?

Loading through the centralized maintenance system

Loading through the Web LMT

Loading through the MAE

Loading through the PnP mode

17. Which of the following commands is used to map DSCPs and VLAN priorities?

MOD PHBMAP

SET DSCPMAP

MOD DSCPMAP

SET PHBMAP

18. Which of the following methods is recommended for modifying the cell bandwidths across the entire network during gNodeB data reconfiguration?

MAE-Deployment (radio network planning data file)

MAE-Deployment (batch reconfiguration)

MML

MAE-Deployment (batch reconfiguration + radio network planning data file)

Facebook Twitter LinkedIn Google + Email